Placement tips fences

A ready-made fence is of course primarily for use in privacy and keep the maximum surface area. Several important points are: easy maintenance, decorative, ability to input their own style and "feel" that you share this fence calls. The well-known boards and piles principle calls less sense, but is an excellent alternative for fast and efficient separation. However, it is convenient to fence parts ready to use. These are available in many different designs, shapes and sizes available at your Garden Deco sale.
Measure the total length of the fence with a tape measure. Share this length by 1.87 and you know how many fence sections you need. The number of fence plus one share, the number of poles that you need. Attention! a legal rule that only you can place the boundary after approval of your neighbors. If this is not the case, you place the fence on your side of the boundary. Hedges for the distance is 50 cm from the boundary. In the backyard, the fence up to 2 meters. high and up to 1 meter in the front yard.

Step 1
Use an auger, available from your dealer Garden Deco. This will create the holes for the posts. Drill holes at least 75 cm deep and 180 feet from each other exactly. Regularly checked to you in perfect vertical drilling. Span a rope around the poles in line.
Sprinkle quick-drying cement into the hole and pour half a bucket of water over it. Stir with a stick well.

Just turn the button worked pole in the wet mortar. Push it so deep that it depends on the place schuttingdeel1.80 to 2.00 meters. above the earth. Bear in mind that the fence section at the bottom 5 inches off the ground and that a garden should always be slightly downward. So let the poles at the lowest point in the garden more above the ground. Adjust the pole pieces of stone with a spirit level and straight. Check the manual for the drying of the concrete. Quick drying cement is just 15 minutes hard, going so quick too.

Check at the top with string and stakes level or the minimum required length above the ground. Get out of the pole at the lowest point in the garden ..

Measure from the bottom of the screen's height between the lines. Be careful when drilling the holes in the pole (3mm) begins at the bottom of the pile, and all measured dimensions of 5 cm increase (on the free hanging from the fence). Screw the fence on the side of the support pole. (See tips)

You can choose to view the fences with the same side to your side of the garden sites. The visible side with most boards here is the best option. Where should the fence separates two gardens, we recommend the sides to view and place. Because most screens are composed of an odd number of boards, the "natural course in this way drawn. Keep the fence sections in place and screw it down to the supports.

Make the final fence to size, by trimming and screws. Press the soil firmly around the poles. Provide the top of the piles with pile Garden Deco ornamentation. This is to avoid unnecessary risk of rain and rot.

Hoarding
Depending on the location of your home, a fence from time to time a good dose of wind. Also, the fence with all kinds of weather to be exposed. The use of well-impregnated garden wood or hardwood is a must. The method of anchoring as described above provides a high degree of certainty on the stand of your fence.

Concrete fence
Placing a concrete fence is basically the same as a wooden fence. You can even make a combination of concrete and wood. Example of concrete pillars and in between the panels of treated wood. Also put this in advance where the good fence on it and turn the place for the concrete posts. Note the distance between these poles. The base boards should be partially buried and therefore in this way is twofold: blocking and anchoring of land (to catch height differences). Keep this in mind when setting the concrete poles. The locations of these poles may likewise be made as a wooden fence. Ensure, by means of a level that the poles are purely vertical stand.

Brick fence
A brick fence can be very nice. Stiffness and stability are very important. Note the adequate foundation, and care for pillars in the fence. A large plane was only half brick built can topple in strong winds.

Fence of boards
To a fence of boards to compile Garden Deco recommends the following: The posts should never exceed 1.80 meters. apart. To create a height of 1.80 meters. with the same "look" like a fence, you need 17 boards (15 boards a screen). A wooden fence is always an odd number of boards. By placing one begins on the side where any number of boards is at the bottom of the pile. After alignment, leveling and securing the first board is using spacers of 6.8 cm. These spacers are placed on the bottom shelf and this is the next shelf down. This board is screwed to the ends. The spacers are now taken to the attachment points further down the board. Because the board is still flexible, the shelf upwards or downwards printed on the blocks. This is a fast and reliable vertical placement guaranteed. Boards should always be screwed to the posts (two screws in the width of the board). Pre-drilling the holes only at the ends of the planks needed. From optical and stability standpoint always a shelf near the poles confirm (deck board). Take care when placing the posts that some poles will act as call forwarding, ie post on this board finishes and a pole will start again (so the pole is only half that time working). If possible ensure that the half-boards in relation to the posts this can be confirmed by the same distance from the poles together and the beginning and end of the various boards and over again on another post to come true. To make a corner joint where the boards will run it at the same level, there are two possibilities. First, placing an additional pole (recommended). Secondly, inserting the first part of a fence beam of 38x67 on the pole with rotating shelves (the shelves over) again in order to create sufficient attachment point for the next piece of fence.